![]() ![]() At the end, zip tie everything as needed. This way, if my mind changes, I have easy access to the wire.ġ4. Sealed end of LED wires with non-adhesive shrink tubing folded on itself and then covered with adhesive shrink tubing. #4RUNNER AMP STEPS INSTALL#I chose not to install LED light because they appear purple/blue, and people have had problems with them. Protects wire and tells you to not try that wire again.ġ3. If positap wrong wire, remove positap and then wrap small amount of electric tape. Make sure boards go up when door closes and down when open.ġ2. Positap a wire of correct color and then touch wire coming from computer, if deploys, you have the right wire. Standard 4Runner power will be the Tundra's 190-hp. #4RUNNER AMP STEPS DRIVER#Know what wire you are looking for, it does no good selecting the right wire for the driver rear door, but then opening the front door. To counter that, expect Land Cruiser to get variable valve timing and a considerable horsepower increase. IMPORTANT: PLACE FUSE IN FIRST, IF NO SPARK, KEEP FUSE IN PLACE AND THEN DISCONNECT AND RECONNECT WIRES TO COMPUTER.ġ0. Trigger automatically when a door is opened or closed Extend and retract in approximately one second Designed for all-weather performance 600 lb. Before using positaps and selecting wires, make sure everything else is done including having the power connected and the amp in place. If you want to see size of wire, you can pull part of weatherstrip up just at where switch is located. The wire colors are correct for the driver and passenger front and rear door courtesy switches. Silicon sealant should be used on floor grommets when passing wire into interior. When putting on black motor housing, don't bother with provided Cinch fasteners, just use small zip ties. Should fall under own weight without motor.Ħ. Snug but don't tighten bolt for motor and linkage assembly until you have tested with board to make sure spacing is correct between board and car when up and no bind is present. Aside from keeping wires away from hot or moving parts.Run wires just inside inner part of thin rubber wheel well and then OVER frame leading to outside of frame where motor and linkage assembly are.ĥ. This is the point of aluminum mounting brackets.Ĥ. KDSS is compatible, but things are tight. Motor assembly goes in the rear door location on both driver and passenger side. Directions are poor, but don't look for videos because they will not follow directions for the model.Ģ. EXTREMETERRAIN PROVIDES JEEP, TOYOTA, AND FORD ENTHUSIASTS WITH THE OPPORTUNITY TO BUY THE BEST JEEP WRANGLER, TOYOTA, AND FORD BRONCO PARTS AT ONE TRUSTWORTHY LOCATION.Ģ003-2022 AMP research power steps and it was a bit of a struggle, but learned some things in the process. THROUGHOUT OUR WEBSITE AND CATALOGS THESE TERMS ARE USED FOR IDENTIFICATION PURPOSES ONLY. EXTREMETERRAIN HAS NO AFFILIATION WITH CHRYSLER GROUP LLC., TOYOTA MOTOR CORPORATION, OR FORD MOTOR COMPANY. FORD, BRONCO,BADLANDS, BIG BEND, BLACK DIAMOND, OUTER BANKS, WILDTRAK, AND ECOBOOST ARE REGISTERED TRADEMARKS OF THE FORD MOTOR COMPANY. TACOMA, TACOMA SR, TACOMA SR-5, TOYOTA RACING DEVELOPMENT (TRD), TACOMA LIMITED, TUNDRA, TUNDRA SR, TUNDRA SR-5, TUNDRA TRD PRO, TUNDRA LIMITED, 4RUNNER, 4RUNNER SR-5, 4RUNNER LIMITED, 4RUNNER NIGHTSHADE, AND 4RUNNER TRD OFFROAD ARE REGISTERED TRADEMARKS OF TOYOTA MOTOR CORPORATION. CHRYSLER, JEEP, JEEP WRANGLER, WRANGLER UNLIMITED, RUBICON, WRANGLER JK, WRANGLER TJ, AND WRANGLER YJ ARE REGISTERED TRADEMARKS OF CHRYSLER GROUP LLC. The PowerStep Running Board provides a clean yet aggressive look for your vehicle with tread design allows for ultimate traction in any condition. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |